Dictionary

babbitt en · NOUN · etymology 1

Pronunciation

• (Received-Pronunciation) audio
• /ˈbæbɪt/ (General-American, Received-Pronunciation)
• /ˈbæbət/ weak vowel merger

Etymology

The noun is derived from Babbitt, the surname of the American inventor Isaac Babbitt (1799–1862) who invented the alloy. The verb is derived from the noun.

Meanings

1. (abbreviation, alt-of, countable, ellipsis, uncountable) Ellipsis of babbitt metal or Babbitt metal (“a soft white alloy of variable composition used in bearings to diminish friction”).
   alt of babbitt metal or Babbitt metal
   • Perhaps the most familiar soft bearing alloys are the babbitts. These have been in use since the early 19th century when printer's type metal was utilized for machinery by casting it into holes drilled in iron housings. […] Babbitt or whitemetal bearing materials represent a class of alloys developed specifically for bearing applications. 1992, William A. Glaeser, “Soft Metal Bearing Materials”, in Materials for Tribology (Tribology Series; 20), Amsterdam; London: Elsevier Science Publishers, →ISBN, page 72:
   • Figure 2 represents a top plan of the "Babbitting" jig, placed in or upon a cast-iron frame, preparatory to the pouring or casting of the "Babbitt" or other soft metal on to or around its journals, to form journal bearings in said cast-iron frame. 1867 October 29, John Underwood, Improved Babbitting and Drilling Jig, US Patent 0070294 (PDF version), page 1:
   • Coins made from nickel babbitt are fairly hard and give a clear bright ring. This makes it easier to pass them due to the widespread belief that a sure test of a counterfeit coin is to drop it on a hard surface to see if it will "ring". […] The simplest test is to cut the edge of a suspected coin with a pocket knife. If it is made of babbitt the metal will pare off quite easily. 1952, Royal Canadian Mounted Police, “Counterfeiting”, in Law and Order in Canadian Democracy: Crime and Police Work in Canada, revised edition, Ottawa: Edmond Cloutier, […], →OCLC, page 209:
   • Remove all sharp edges from the babbitt with a chisel or file and try the shaft after removing the paper wrapping for a fit. If a light coat of oil mixed with lampblack be smeared on the shaft and the shaft revolved, the lampblack will catch on the high points of the babbitt, then by removing the shaft and scraping off these high spots a good bearing can be produced. 1919 March, “Babbitting Bearings”, in Care and Repair of Farm Implements. No. 5.—Grain Separators (U.S. Department of Agriculture Farmers’ Bulletin; 1036), Washington, D.C.: Government Printing Office, published 1920, →OCLC, page 14:
   • The cross-head is cast of crucible steel and faced with Babbitt. […] The rod is secured to the crank pin by body bound bolts, this bearing being provided with Babbitt shells which are prevented from turning by paper liners extending to the pin. 1895 June, “The Fisher Self-oiling Engine”, in Power, volume XV, number 6, New York, N.Y.; Chicago, Ill.: McGraw-Hill Publishing Company, →ISSN, →OCLC, page 10, column 2:
   • In most applications, the inner bearing surface is made of a thin layer of a soft white metal (babbitt), which has a low melting temperature. 2003, Avraham Harnoy, “Design Charts for Finite-length Journal Bearings”, in Bearing Design in Machinery: Engineering Tribology and Lubrication, New York, N.Y.; Basel: Marcel Dekker, →ISBN, page 164:
   • Running while low on oil had galled the babbitt.
   • Babbitts may be lead-based (as 75%Pb, 15%Sb, 10%Sn) or tin-based (as 89%Pb, 3%Cu). They use lead or tin as a soft matrix metal and hard particles of Sb-Sn or Cu-Sn to resist wear. Because of their softness, babbitts are unrivalled in conformability and embeddability. […] Because of low strength and high cost, a thin babbitt overlay, usually about 0.025 mm, is often deposited as liners over steel bushings to combine the great load carrying capacity of steel with conformability and corrosion resistan[ce] of babbitts. 2019, Wei Jiang, “Sliding Bearings”, in Analysis and Design of Machine Elements, Singapore: John Wiley & Sons Singapore, →ISBN, page 350:

Forms

Synonyms

Babbitt's metal

Translations (10)

ru ба́ббит (soft white alloy of variable composition — see also babbitt metal) · pl babbit (soft white alloy of variable composition — see also babbitt metal) · ro babbit (soft white alloy of variable composition — see also babbitt metal) · be бабіт (soft white alloy of variable composition — see also babbitt metal) · bg бабит (soft white alloy of variable composition — see also babbitt metal) · id babit (soft white alloy of variable composition — see also babbitt metal) · fi valkometalli (soft white alloy of variable composition — see also babbitt metal) · et babiit (soft white alloy of variable composition — see also babbitt metal) · kk баббит (soft white alloy of variable composition — see also babbitt metal) · uk бабіт (soft white alloy of variable composition — see also babbitt metal)

wikipedia: Isaac Babbitt

babbitt en · VERB · etymology 1

Pronunciation

• (Received-Pronunciation) audio
• /ˈbæbɪt/ (General-American, Received-Pronunciation)
• /ˈbæbət/ weak vowel merger

Etymology

The noun is derived from Babbitt, the surname of the American inventor Isaac Babbitt (1799–1862) who invented the alloy. The verb is derived from the noun.

Meanings

1. (transitive) To line (something) with babbitt metal to reduce friction.
   • The caps for these journal-boxes or bearings may be Babbited by this same jig, and they would, of course, exactly conform to the other portions of the bearings in the frame. […] This drilling jig is a negative of the interior of the frame. It has two sets of bearings, c d and e f, which are at right angles to each other, and which set in the longitudinal and transverse bearings that have been made and "Babbited" in the cast frame, and thus steady and hold it. 1867 October 29, John Underwood, Improved Babbitting and Drilling Jig, US Patent 0070294 (PDF version), page 1:
   • The main bearings were babbitted and line-bored.
   • The common way may be described as babbitting one-half of the bearing at a time: then by means of pasteboard liners between the halves, making the other half complete. […] It takes half the time required to babbitt the bearings in halves. 1920 July, R. C. Leibe, “A Quick Way to Babbitt”, in Waldemar Kaempffert, editor, The Popular Science Monthly, volume 97, number 1, New York, N.Y.: Modern Publishing Company, →OCLC, page 98, column 2:
   • These bearings, with their caps, are babbitted with metal of the finest quality, a jig representing the shafting being used to locate and regulate the proportion of the bearing precisely. 1872, “[Claims for the Gold Medal for 1870. Second Department.] Statement of Linforth, Kellogg & Co., of San Francisco.”, in Transactions of the California State Agricultural Society during the Years 1870 and 1871, volume III, Sacramento, Calif.: T. A. Springer, →OCLC, page 145:
   • The work of babbitting bearings offers considerable opportunity for the use of different forms of fixtures that are capable of making a material increase in the efficiency with which this operation can be carried on. 1912 June, J. A. H. Phillips, “Forms of Babbitting Fixtures”, in Wood Craft: A Journal of Woodworking, […], Cleveland, Oh.: Gardner Print Co., →OCLC:
   • To babbitt any kind of box, first chip out all of the old babbitt and clean the shaft and box thoroughly with benzine. […] In babbitting a solid box cover the shaft with paper, draw it smooth and tight, and fasten the lapped ends with mucilage. 2015, Fred D. Crawshaw, E[mil] W. Lehmann, Byron D[avid] Halsted, James H. Stephenson, Ultimate Guide to Farm Mechanics: A Practical How-to Guide for the Farmer, New York, N.Y.: Skyhorse Publishing, →ISBN, page 600:

Forms

Translations (2)

pl oprawiać babbitem (to line (something) with babbitt metal to reduce friction) · pl oprawić babbitem (to line (something) with babbitt metal to reduce friction)

wikipedia: Isaac Babbitt

babbitt en · NOUN · etymology 2

Pronunciation

• (Received-Pronunciation) audio
• /ˈbæbɪt/ (General-American, Received-Pronunciation)
• /ˈbæbət/ weak vowel merger

Etymology

From Babbitt, the surname of George Babbitt, the title character of the novel Babbitt (1922) by the American author Sinclair Lewis (1885–1951). The word was also popularized by the George (1898–1937) and Ira Gershwin (1896–1983) song “The Babbitt and the Bromide”, first featured in the 1927 musical Funny Face and later in the film Ziegfeld Follies (1945).

Meanings

1. (US, alt-of, dated) Alternative letter-case form of Babbitt (“a person who subscribes complacently to materialistic middle-class ideals”).
   alt of Babbitt
   • Ira relished telling the story that Fred Astaire took him aside and said he knew what a babbitt was, but what was a bromide? 2003, William Hyland, George Gershwin: a new biography, Greenwood Publishing Group, page 116:
   • One speaks of a babbitt habit, a babbitt era. Nothing is more true. America recognized itself in Babbitt, it demurred, but it also admired. 1930, The Literary digest, volume 105, Funk and Wagnalls, page 21:
   • … a "babbitt" is a person full of self-confident bluster who is nevertheless a narrowminded philistine and a hypocrite.] 2002 Tamkang review, Volume 33, Tamkang College of Arts and Sciences, p.158

Forms

Deriveds

babbittry · Babbittry

wikipedia: Ira Gershwin · wikipedia: Sinclair Lewis · wikipedia: Ziegfeld Follies